PROBE-N0S-6000 PosiTector® Coating Thickness Gauge Cabled 0-Degree Micro Probe, Measures Coatings on NON-Ferrous Metals up to 25 mils / 625 Microns. PROBE ONLY, Display Sold Separately PRBN0S

• Each probe retains its own unique calibration information (allowing full probe interchangeability)
• Heavy-duty, gold-plated locking connector for industrial environments
• Probes are PosiTector SmartLink compatible - wirelessly connect PosiTector 6000 probes to your smart device
• Extended cables available for underwater or remote measuring. Specify length when ordering
• Temperature maximum for most probes is 125-degrees F. Probe FHXS has maximum operating temperature of 500-degrees F.
• Certificate of Calibration (Long Form) traceable to NIST or PTB included with every probe
• Two (2) year probe warranty

F - for ferrous metals (steel and cast iron)
N - for non-ferrous metals (aluminum, copper, titanium, etc.)
FN - for all metal substrates - Automatically recognizes the substrate and takes a measurement

F, N, FN, FT
Ideal for one-handed operation

Probe Model:	F	N	FN	FT
Range:	0 - 60 mils			0 - 250 mils
	0 - 1500 µm			0 - 6 mm 0 - 6000 µm
*Accuracy:	± (0.05 mils + 1%) 0 - 2 mils ± (0.1 mils + 1%) > 2 mils			± (0.5 mils + 1%) 0 - 100 mils ± (0.5 mil + 3%) > 100 mils
	± (1 µm + 1%) 0 - 50 µm ± (2 µm + 1%) > 50 µm			± (0.01 mm + 1%) 0 - 2.5 mm ± (0.01 mm + 3%) > 2.5 mm

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

FS, NS, FNS, NAS, FTS
These constant-pressure, stainless steel probes are hermetically sealed to be totally waterproof - ideal for underwater use.

Probe Model:	FS	NS	FNS	NAS	FTS
Range:	0 - 60 mils			0 - 25 mils	0 - 250 mils
	0 - 1500 µm			0 - 625 µm	0 - 6 mm 0 - 6000 µm
*Accuracy:	± (0.05 mils + 1%) 0 - 2 mils ± (0.1 mils + 1%) > 2 mils			± (0.02 mils + 1%) 0 - 4 mils ± (0.1 mil + 3%) > 4 mils	± (0.5 mils + 1%) 0 - 100 mils ± (0.5 mil + 3%) > 100 mils
	± (1 µm + 1%) 0 - 50 µm ± (2 µm + 1%) > 50 µm			± (0.5 µm + 1%) 0 - 100 µm ± (2 µm + 3%) > 100 µm	± (0.01 mm + 1%) 0 - 2.5 mm ± (0.01 mm + 3%) > 2.5 mm

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

Uniquely designed for rugged applications. The FXS Xtreme™ probe with zirconia-toughened alumina wear face is ideal for rough steel surfaces.

Enhanced measuring speed of 50+ readings per minute makes it ideal for measuring large, rough surfaces quickly. Scan mode increases measurement rate to over 100 readings per minute (PosiTector Advanced only).

Compatible with PosiTector bodies with serial numbers greater than 700,000.

Probe Model:	FXS Xtreme™
Range:	0 - 60 mils
	0 - 1500 µm
*Accuracy:	± (0.05 mils + 1%) 0 - 2 mils ± (0.1 mils + 1%) > 2 mils
	± (1 µm + 1%) 0 - 50 µm ± (2 µm + 1%) > 50 µm

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

FRS, NRS, FNRS
Right angle probe for measuring within areas of low headroom.

These constant-pressure, stainless steel probes are hermetically sealed to be totally waterproof - ideal for underwater use.

Probe Model:	FRS	NRS	FNRS
Range:	0 - 60 mils
	0 - 1500 µm
*Accuracy:	± (0.05 mils + 1%) 0 - 2 mils ± (0.1 mils + 1%) > 2 mils
	± (1 µm + 1%) 0 - 50 µm ± (2 µm + 1%) > 50 µm

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

The PosiTector^® 6000 FNDS probe measures the individual thicknesses of both the paint and the zinc layers in a duplex coating system with a single reading.

Duplex coating systems use a combination of two corrosion protection systems – typically paint or powder coating over galvanized steel (hot-dip, electro or zinc spray metallizing). The resultant corrosion protection is superior to either protection system used independently.

In Duplex mode, the PosiTector^® 6000 FNDS utilizes both magnetic (ferrous) and eddy current (non-ferrous) principles simultaneously to calculate and display the individual paint and zinc layer thicknesses. The magnetic principle is used to measure the combined paint/zinc thickness over the ferrous substrate, and the eddy current principle is used to measure the paint thickness over the non-ferrous zinc coating. The zinc thickness is calculated by subtracting the paint thickness from the combined paint/zinc thickness measurement.

When disabled, the gage will operate like a conventional combination ferrous/non-ferrous instrument (similar to the PosiTector^® 6000 FNS probe). Ideal for measuring non-magnetic coatings over steel and non-conductive coatings over non-ferrous metal substrates.

Compatible with PosiTector^® Advanced (serial numbers 730,000+) and PosiTector Standard gage bodies with a color display. A Simple gage update may be required.

Probe Model:	FNDS
Range:	0 - 60 mils 0 - 1500 µm
Duplex Mode
Minimum Zinc Thickness:	0.5 mil (13 µm)
Paint Layer Accuracy*:	± (0.05 mils + 1%) 0 - 2 mils ± (0.1 mils + 1%) > 2 mils
	± (1 µm + 1%) 0 - 50 µm ± (2 µm + 1%) > 50 µm
Zinc Layer Accuracy*:	± (0.1 mils + 1%) 0.5 - 2 mils ± (0.2 mils + 1%) > 2 mils
	± (2 µm + 1%) 13 - 50 µm ± (4 µm + 1%) > 50 µm

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

F0S, N0S
With our smallest measuring tip and best thin-film accuracy, this instrument is ideal for measuring on small parts, hard-to-reach areas, or close to edges.

The straight F0S and N0S Microprobes have a quick release adapter that makes them constant pressure probes for alignment on small, flat or curved parts. This adapter is held in place by a spring. If the sleeve is not required, simply pull it off the probe.

Probe Model:	F0S	N0S
Range:	0 - 45 mils	0 - 25 mils
	0 - 1150 µm	0 - 625 µm
*Accuracy:	± (0.02 mils + 1%) 0 - 4 mils ± (0.1 mils + 1%) > 4 mils
	± (0.5 µm + 1%) 0 - 100 µm ± (2 µm + 1%) > 100 µm

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

F45S, N45S
With our smallest measuring tip and best thin-film accuracy, this instrument is ideal for measuring on small parts, hard-to-reach areas, or close to edges.

Probe Model:	F45S	N45S
Range:	0 - 45 mils	0 - 25 mils
	0 - 1150 µm	0 - 625 µm
*Accuracy:	± (0.02 mils + 1%) 0 - 4 mils ± (0.1 mils + 1%) > 4 mils
	± (0.5 µm + 1%) 0 - 100 µm ± (2 µm + 1%) > 100 µm

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

F90S, N90S
Right angle probe for measuring within areas of low headroom.

With our smallest measuring tip and best thin-film accuracy, this instrument is ideal for measuring on small parts, hard-to-reach areas, or close to edges.

Probe Model:	F90S	N90S
Range:	0 - 45 mils	0 - 25 mils
	0 - 1150 µm	0 - 625 µm
*Accuracy:	± (0.02 mils + 1%) 0 - 4 mils ± (0.1 mils + 1%) > 4 mils
	± (0.5 µm + 1%) 0 - 100 µm ± (2 µm + 1%) > 100 µm

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

F90ES
Right angle extended length (350 mm / 13.75") probe for measuring within areas of low headroom.

With our smallest measuring tip, longest probe length and best thin-film accuracy, this instrument is ideal for measuring on small parts, hard-to-reach areas, or close to edges.

Probe Model:	F90ES
Range:	0 - 45 mils
	0 - 1150 µm
*Accuracy:	± (0.02 mils + 1%) 0 - 4 mils ± (0.1 mils + 1%) > 4 mils
	± (0.5 µm + 1%) 0 - 100 µm ± (2 µm + 1%) > 100 µm

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

FT, FTS, FTRS, FNTS, FKS, NKS
Ideal for thick protective coatings such as epoxy, rubber, concrete liners, intumescent fireproofing and more.

FT

FTRS

FTS

FNTS, FKS, NKS

Measure non-conductive coatings on steel substrates.

FHXS Xtreme™ probe with Alumina wear face and braided cable for hot or rough surfaces.

Hot surfaces up to 250°ree; C (500°ree; F).Compatible with PosiTector bodies with serial numbers greater than 700,000 and the new PosiTector SmartLink.

Probe Model:	FHXS Xtreme™
Range:	0 - 400 mils 0 - 10,000 µm
*Accuracy:	± (0.1 mils + 3%) ± (2 µm + 3%)

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

Measures intumescent paint and other thick protective coatings on steel.

• Measures up to 38 mm (1.5 inches)
• Braided stainless steel cable - kink-proof, wear and cut resistant
• Includes hard shell case and 19 mm (750 mil) shim

Probe Model:	FLS
Range:	0 - 38 mm 0 - 1.5 inches
*Accuracy:	± (0.01 inches + 3%) ± (0.2 mm + 3%)
Minimum Surface Area:	3.25 x 3.25 inches (83 x 83 mm)
Minimum Substrate Thickness:	0.1 inches (2.5 mm)

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.

Measures very thick coatings on ALL metals. Ideal for measuring ship hull coatings and thick intumescent paints.

• Measures up to 63.5 mm (2.5 inches)
• Measures non-conductive coatings on both ferrous and non-ferrous metal substrates
• Braided stainless steel cable - kink-proof, wear and cut resistant
• Long-lasting, low wear probe face to facilitate scanning of large surfaces
• Includes a handle for easy one-handed operation
• Includes a set of traceable coating thickness standards

Probe Model:	FNGS
Range:	0 - 63.5 mm 0 - 2.5 inches
*Accuracy:	± (0.01 inches + 3%) ± (0.2 mm + 3%)
Minimum Surface Area:	10 x 10 inches (254 x 254 mm)
Minimum Substrate Thickness:	0.2 inches (5 mm)

*Accuracies are stated as a fixed value plus a percentage of the gage's actual reading.